We – EPG Group the greatest gearbox & motors , couplings and gears manufacturing unit in China with 5 distinct branches. For much more specifics: Cell/whatsapp/telegram/Kakao us at: 0086~13083988828 13858117778083988828

How to Go through:

090ZE 20 ()  (S1) -750 T1
a      b    c   d   e    f       g
 

a:  Body Dimensions: 090 =90mm

b: Sequence code:     ZE:      Round mounting flange sequence

c: Reduction Ratio:     Solitary Phase:  3,4,5,6,7,8,9,ten     Two Levels:    fifteen,20,25,30,35,forty,45,fifty,sixty,70,eighty,90,a hundred

d: Backlash:     Solitary Stage: ≤8arc.min       Two Stages:   ≤12arc.min

e: Enter shaft variety:            S1: Loc ept with loc ept ring (Regardless regardless of whether the motor with keyway can use it. But “D” lower can’t be used)      S2: Loc ept with keyway (Enter shaft with key)      A:  Other kinds (Make sure you make contact with with us)

f: Applicable servo motor power (W),Please get in touch with us for specific electrical power

g: Remember to make contact with us for the mouting type of the flange

 

Spesifications of Different Ratio: 

Product Type	Unit	090	Reduction Ratio	Quantity Of Phase
Rated Output Torque	N.M	a hundred thirty	three	1
		one hundred forty	4
		a hundred and sixty	five
		a hundred and fifty	six
		a hundred and forty	7
		a hundred and twenty	8
		one hundred	9
		100	ten
		one hundred thirty	15	two
		one hundred forty	20
		one hundred sixty	25
		a hundred and fifty	thirty
		one hundred forty	35
		one hundred twenty	forty
		one hundred	45
		a hundred and sixty	fifty
		a hundred and fifty	sixty
		140	70
		one hundred twenty	eighty
		100	90
		one hundred	a hundred
Max radial torque		2985	/
Max Axial torque		1625	/
Full Load Effectiveness	%	97	/	one
		94	/	2
		/	/	/
Backlash	arc.min	≤8	/	one
		≤12	/	2
		/	/	/

Demensions(Device: mm):  

 

Solution variety

D1

D2

D3h6

D4g6

D5

D6

D7

L1

L2

L3

L4

L5

L6

090ZE

80

M6X.1P

22

68

M8X.1.25P

104

90

31.five

46

8

36

32

3

L7

L8

L9

C1

C2

C3

C4

C5G6

C6

C7

C8

C9

B1h9

H1

twelve

eighty

19

a hundred

M6X1P

*≤19/≤24

40.5

eighty

four

ninety

17.five

143.5

6

24.5

*C3≤16 is avialble for 070ZE ratio 5 and ratio 10

Firm Introduction :

—- About Us—-

Professional Gearbox and Motor Manufacture

HangZhou ept Chief Clever Transmission Co., Ltd. Was recognized in August 2006. It is an electromechanical automation enterprise integrating R&D, producing, income and provider of motor drivers, little and particular electric powered equipment and precision reducers. It has 3 branches, 4 subsidiaries, and a lot more than 1, 500 workers, with a registered funds of eighty million yuan, covering an spot of 66667 square meters In August 29, 2017, it was shown on the HangZhou Stock Exchange’s SME board A shares (stock code 57196) In 2019, it recognized an working income of 676 million RMB.

Manufacture Procedure:

Certification:

Exhibition: 

FAQ:

Q: What’re your main merchandise?
A: We presently generate Brushed DC Motors, Brushed DC Gear Motors, Planetary DC Gear Motors, Brushless DC Motors, AC Motors, Large Precision Planetary Gearbox and Precision Cycloidal Gearbox and many others.. You can check the requirements for above motors on our internet site and you can e mail us to advise required motors for each your specification also.

Q: How to choose a ideal motor or gearbox?
A:If you have motor photographs or drawings to display us, or you have thorough requirements, these kinds of as, voltage, velocity, torque, motor measurement, wor ept method of the motor, required life time and sounds degree etc, make sure you do not hesitate to permit us know, then we can recommend suitable motor for each your ask for accordingly.

Q: Do you have a customized support for your common motors or gearboxes?
A: Sure, we can personalize for every your request for the voltage, speed, torque and shaft dimension/form. If you need to have additional wires/cables soldered on the terminal or need to have to insert connectors, or capacitors or EMC we can make it way too.

Q: Do you have an person layout provider for motors?
A: Yes, we would like to style motors independently for our buyers, but some variety of  molds are necessory to be developped which might want actual expense and design and style charging. 

Q: What’s your direct time?
A: Generally talking, our standard standard product will need fifteen-30days, a bit longer for tailored goods. But we are very versatile on the lead time, it will count on the certain orders.

  

 

The use of first products manufacturer’s (OEM) element figures or emblems , e.g. CASE® and John Deere® are for reference purposes only and for indicating solution use and compatibility. Our company and the listed alternative parts contained herein are not sponsored, authorized, or produced by the OEM.